Scania Opticruise Manual Pdf

The information in this Operator's manual was correct at the time of going to press. It is simple and always possible to change gears manually with the lever. Start the engine and check that no leakage occurs. Check the drive belt for cracks. The vehicle may be weakened, which can have a negative affect on lifting points.

Carry the belt pretensioner with the mouth of the detonator pointing downwards. Wear protective gloves and goggles.

Scania Opticruise Always in the right gear

Scania Dismantling Manual

Handle empty accumulator tanks in compliance with local regulations. The airbag must be handled and stored in compliance with local regulations. This should also be taken into consideration when tilting cabs.

Scania - Truck Tractor & Forklift Manual PDF DTC

Engine Data Plate Code for application. Avoid skin contact with ashes. Isocyanates are found in some paints, putties, adhesives and plastic foams, etc. This website uses cookies.

Opticruise Scania s Automated Manual Transmission CV news

Manualslib has more than 73 Scania manuals

Manualslib has more than 73 Scania manuals

Important information

Scania recommends using Tegera gloves. When carrying out all forms of hot work, the relevant safety regulations for this type of work should be followed The vehicle may be weakened, which can have a negative affect on lifting points. The oil will now be returned to the filling equipment tank. The refrigerant generates a very toxic gas when heated. This applies for example to grinding, welding and cutting products to which a top coat of paint containing isocyanates has been applied.

This warning symbol and text can be found next to those maintenance items where it is particularly impor-. The particle filter will be very hot after driving. Handle and store the belt pretensioner in compliance with local regulations. Wash off any preservative oil on the outside using white spirit. Skip to toolbar About WordPress.

Hill-hold is standard feature enabling a complete control during acceleration in gradients. Fill in the particulars from the start-up report below as well. The automatic clutch has a high-precision electro-hydraulic control system, which is an industry first. Assemble the charge air cooler.

Scania Opticruise Always in the right gear

The information is applicable to all Scania models. Related Searches Scania Scania manual Scania workshop manual.

Opticruise Scania s Automated Manual Transmission CV news

For this reason, always secure the starting device or disconnect a battery cable before working on the engine. Checking Sacrificial Anodes Drain the sea water circuit as described in Draining the sea water circuit.

Do not hold your fingers over the detonator or on the cable. Pre- pare for the next start by connecting the en- gine heater if fitted. Already in October leadership began merger talks with its main competitors, and in March were obledeneny venture to manufacture cars.

Scania corrosion inhibitor, ethylene glycol and other coolant additives are highly toxic and can be fatal when swallowed. Through advanced real-time mathematical calculations, Opticruise knows when to ramp down the torque in the engine. With Opticruise, multicore processors pdf gear changing is optimised for the best possible fuel consumption. The main advantage of Scania Opticruise is that it calculates the most suitable gear to use according to parameters it gets from the sensors in order to deliver maximum energy efficiency.

Fuel filter and oil filter Hand in to an authorised waste disposal contractor. Where there are more than one variant of a part, the codes of both materials will be stated. Use a face mask, protective goggles and gloves when handling the particle filter. Tighten the lock nut after adjustment. The refrigerant must not be released into the atmosphere but must be recycled according to local regulations.

Colours and a material code identify polymer materials. If work is to be carried out underneath the cab later, make sure the cab is tilted before emptying the pump. When working on the engine, for example when adjusting drive belts and the clutch, or when changing the.

Handle empty compressed air tanks in compliance with local regulations. For this reason, make sure that there is adequate ventilation in the areas where the work is carried out. The volumes are approximate.

Make sure that the drainage starts. When fitting the new impeller, bend the vanes in the same direction as on the old one.

Important information